Truckers Report Jobs

Find Trucking Jobs

Company Driver Company Driver Dry Van Dry Van Flatbed Flatbed Refrigerated Refrigerated Specialized Specialized Owner Operator Owner Operator
More Trucking Job Searches ⌄ Fewer Trucking Job Searches
⌃

Where to get a ECM wiring harness for a N14 Cummins

Discussion in 'Experienced Truckers' Advice' started by Tabby101, May 21, 2018.

Page 1 of 2
  1. May 21, 2018 #1
    Tabby101

    Tabby101 Bobtail Member

    6
    0
    May 21, 2018
    0
    I need to find a place that has an ECM harness for a N14 cummins. I havesearched around and can't seem to find one under $300.:mad:Any ideas ofjunkyards or used parts stores?
     
    Tabby101, May 21, 2018
    Tabby101, May 21, 2018
    #1
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. May 21, 2018 #2
    mrbamcclain

    mrbamcclain Light Load Member

    258
    116
    May 25, 2011
    Hammond, La
    0
    mrbamcclain, May 21, 2018
    mrbamcclain, May 21, 2018
    #2
    Tabby101 Thanks this.
  4. May 22, 2018 #3
    Ridgeline

    Ridgeline Road Train Member

    22,599
    119,963
    Dec 18, 2011
    Michigan
    0
    Between I think the other two threads from the op, everyone tells the op buy new.
     
    Ridgeline, May 22, 2018
    Ridgeline, May 22, 2018
    #3
    Lepton1 and Tabby101 Thank this.
  5. May 22, 2018 #4
    Tabby101

    Tabby101 Bobtail Member

    6
    0
    May 21, 2018
    0
    UPDATE
    So it seems I do not need the entire harness. All I need is the small plug from the engine...the one with the least amount of wires. Mine was cut about 8 inches back. I ordered one from a junkyard of North for 75 bucks. The problem I have now is the wires are not numbered or colored the same as mine. The plug actually fits I just have no way of knowing which wire's to connect.
     
    Tabby101, May 22, 2018
    Tabby101, May 22, 2018
    #4
  7. May 22, 2018 #5
    spindrift

    spindrift Road Train Member

    3,233
    12,905
    Dec 2, 2014
    Texas
    0
    The wires should be numbered.
     
    spindrift, May 22, 2018
    spindrift, May 22, 2018
    #5
  8. May 22, 2018 #6
    Ridgeline

    Ridgeline Road Train Member

    22,599
    119,963
    Dec 18, 2011
    Michigan
    0
    If I remember right, you have to have a special tool to remove the contacts on the plug.
     
    Ridgeline, May 22, 2018
    Ridgeline, May 22, 2018
    #6
  9. May 22, 2018 #7
    mrbamcclain

    mrbamcclain Light Load Member

    258
    116
    May 25, 2011
    Hammond, La
    0
    Even more reason you should have just bought a new harness. Chasing unknown wires is just more time wasted.
     
    mrbamcclain, May 22, 2018
    mrbamcclain, May 22, 2018
    #7
  10. May 22, 2018 #8
    spindrift

    spindrift Road Train Member

    3,233
    12,905
    Dec 2, 2014
    Texas
    0
    True...special tool needed to remove the pins from the harness connector.
     
    spindrift, May 22, 2018
    spindrift, May 22, 2018
    #8
  11. May 23, 2018 #9
    Tabby101

    Tabby101 Bobtail Member

    6
    0
    May 21, 2018
    0
    They are numbered but none of them match.
     
    Tabby101, May 23, 2018
    Tabby101, May 23, 2018
    #9
  12. May 23, 2018 #10
    Tabby101

    Tabby101 Bobtail Member

    6
    0
    May 21, 2018
    0
    Yes you do need a special tool and it was an ex-employee with a vindictive streak.
     
    Tabby101, May 23, 2018
    Tabby101, May 23, 2018
    #10
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

    • Page 1 of 2