why are my steer tires cupping?

Discussion in 'Trucks [ Eighteen Wheelers ]' started by bosshogg, Dec 6, 2010.

  1. bosshogg

    bosshogg Bobtail Member

    13
    2
    Dec 5, 2010
    detroit michigan
    0
    i have a 01 w900 and my front steer tires are cupping. the air pressures is always checked and always good. i have been told it could be from bad shocks...
     
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. country29

    country29 Medium Load Member

    518
    157
    Feb 27, 2010
    Arkansas
    0
    could be shocks, probably alignment. check your kingpins and wheel bearings for slack, if no slack then I would put 2 steer shocks on and get a good 3axle align. what pressures are you running and when are you checking them?
     
    BUMBACLADWAR and 3rd Gen Driver Thank this.
  4. Powder Joints

    Powder Joints Subjective Prognosticator

    7,506
    7,414
    Sep 25, 2007
    Rosamond, SoCal
    0
    Always good, would that be 85 psi, 90, 100, 110. Low air pressure along with alignment, mostly alignment but the low pressure will cause it to show faster.

    I run my steers at 100 psi for 75,000 miles then move them to the trailers.
     
  5. Winchester Magnum

    Winchester Magnum Road Train Member

    1,492
    1,647
    Jan 4, 2009
    Alaska highway
    0
    If one tire is cupped on the inside, and the other is cupped on the outside, you need a three axle alignment.
     
  6. blackw900

    blackw900 The Grandfather of Flatbed

    5,817
    7,678
    Jul 12, 2009
    A.W.O.L
    0
    Make sure that when you get the alignment done, They check the caster. Mine was cupping badly and I was getting around 45,000 miles from a set of steers and the front end shop kept saying that everything was fine...They weren't checking the caster.

    Then I went to a different front end shop!

    I now have over 100,000 miles on my steers and have no sign of cupping.
     
  7. target_driver

    target_driver Light Load Member

    73
    19
    Dec 18, 2009
    Iowa
    0
    caster is NOT a tire wearing alignment angle....... camber is....... as is toe but caster is NOT. are you pulling the same trailer? or different trailers???? also is your 5th wheel greased properly?
     
  8. DL550CAT

    DL550CAT Road Train Member

    1,427
    1,482
    Oct 18, 2009
    Waynesburg, Pa
    0
    Camber has to be way off to cause tire wear on a radial its more likely to cause the truck to pull. Sounds like shocks or suspension trouble. I agree with Country29
     
    BUMBACLADWAR Thanks this.
  9. bosshogg

    bosshogg Bobtail Member

    13
    2
    Dec 5, 2010
    detroit michigan
    0
    It is pulling to the left and it is only the right tire cupping, I run the air pressure between 105 and 110
     
  10. Trouble65

    Trouble65 Medium Load Member

    621
    147
    Jan 11, 2009
    Ontario Canada
    0
    All of the above are valid points. The other area you might need to look at is your trailer alignment. If you pull the same trailer all of the time it might cause be the problem. However if you pull different trailers then that might not be a problem.
     
  11. Heavyd

    Heavyd Road Train Member

    7,749
    6,184
    Feb 4, 2009
    0
    Cupping is rarely alignment related. Alignment will effect the whole circumference of the tire, not spots here and there. Cupping is caused by inconsistent contact with the road surface. You are looking at tire balance, tire out of round(bad mounting), shocks, springs, pressure or tire quality. Alignments will not fix cupping. If you are running tires made in Japan or Asia, sorry to say, but they never seem to wear properly no matter how good you keep your truck maintained.
     
    ProPilot Thanks this.
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.